Plumbing News and Tips for Homeowners in the Raleigh NC Area, New Product Reviews, Water Heaters and Tankless water heater advice from local certified plumbers.

Extending-Your-Water-Heaters-Lifespan

Extending Your Water Heaters Lifespan

When first purchasing a water heater, many factors can weigh into your selection process. Upon completing the proper research and settling on a specific unit that best fits your needs, you then want to keep up with maintenance. In an effort to help you maximize your purchase, this post will offer up some pointers to help you with Extending Your Water Heater Lifespan. In following these easy tips, you will not only optimize its efficiency but also save yourself money in the long run.

How Long Should My Water Heater Last?

This is a very valid question that basically anyone purchasing a water heater would be curious about. The actual answer to this question may vary slightly depending on your brand, type, or usage. However, generally, a water heater will work perfectly for a decade and in some cases longer. 

While ten years is a long time, why not take a few simple measures towards Extending Your Water Heaters Lifespan? With just a few easy maintenance tips and regular checking, you can make the heater last longer, while running safer and more efficiently.

Expanding-Your-Water-Heaters-Lifespan-Poole's-Plumbing

Testing the valve on your water heater is your very important first step

Tips for Extending Your Water Heaters Lifespan: Step One…the Valve Test

To begin with our water heater’s maintenance check, we will analyze the unit’s valve. This can be as easy as one action “test,” if all goes right upon our first method of checking. Regardless, even if it comes to a valve replacement, this is a simple procedure and one that is important in Extending Your Water Heaters Lifespan.

1- Test the Valve

 Our first tip in Extending Your Water Heaters Lifespan will have you taking a look at the valve. In case you aren’t sure, the valve can be found on the top or side of the unit. A function of the valve is to open automatically if the pressure has got too high in the tank. The tank could actually explode if the pressure were to get too high.

To test your valve, all you will need is an empty bucket. Then first, place the bucket under the water heater’s discharge pipe. Next, lift the lever on your pressure relief valve gently. This should release the water from the tank into your bucket. Consequently, by the water emptying out, you know that the valve is working correctly.

2- Replace the Valve (If Needed)

Just to be 100 percent clear, this step is unnecessary if the water empties from the tank as it should in the previous step. That being said, if the water does not empty, it is time to replace the valve in the best interest of Extending Your Water Heaters Lifespan.

This may sound like a big undertaking, however, replacing your valve in actuality, could not be simpler. To start the process, turn off the water, drain the tank, and unscrew the discharge pipe. Once these three steps are finished, next unscrew the old valve. Next, you will wrap the threads of the new valve you are installing with sealant tape and then screw it in. 

Extending-Your-Water-Heaters-Lifespan- Pooles

Draining your tank is essential to remove all sediment and debris.

To be sure this step is complete in this process of Extending Your Water Heaters Lifespan, check now for a leak. If the valve you replace was several years old, or never had been tested, it may leak. If that is the case, you need to replace the valve.

3-Check all of Your Work

It never hurts on any job to double-check your work and be sure that it is done correctly. To begin our check here, first close the shutoff valve. This valve is the one on the cold water supply which feeds your water heater. After this has been closed, turn on the hot water of any faucet in your home. 

This will release all pressure inside the water heater’s tank. If you have an electric unit, you will want to turn the power off at your main panel. Those with gas water heaters will simply turn the gas control dial to the off position. 

Tips for Extending Your Water Heaters Lifespan: Step Two…Drain the Tank

After you have completed checking the valves, step two in Extending Your Water Heaters Lifespan is draining the tank. More specifically, this part of our process is to flush any sediments or debris out of the bottom of the tank. The reasoning behind this is that the buildup of sediment in your tank will shorten the life of your water heater. Likewise, the sediment being present makes your unit have to work harder which equals a higher energy bill. Because there are many issues that can come about from sediment or debris in your tank, our next blog article will actually solely focus on draining your tank.

Most times when draining your tank, you will empty two or three gallons to be sure and get all sediment removed. However, always be sure to let the water flow out of the tank until you are no longer seeing any particles in the water. Basically, you are slowly opening the drain valve and letting all water run out until it’s is clear of any debris.

Tips for Extending Your Water Heaters Lifespan: Step Three…a Double Check and a Listen

Expanding-Your-Water-Heaters-Lifespan-Pooles-Plumbing

One of your last steps is to relight the pilot and restart your unit.

As you are readying to restart your water heater, there is no need to worry about a few noises you may hear. The sounds spoke of would resemble a gurgling or almost groaning type sound coming from your water heater. This is not anything to be alarmed by, it is simply the noise from air entering the system as the water drains.

That being said, you now want to be sure that your drain valve was closed tightly. If it does not, drain the tank completely, and replace that valve with a new one. Then you will want to restart your unit. Again, don’t worry about any gurgling or groaning noises coming from the heater. That sound is just air entering the system as water drains out. 

Tips for Extending Your Water Heaters Lifespan: Step Four…Time for a Restart

To continue with our final step in Extending Your Water Heaters Lifespan, we are going to restart the unit. To do so, open the shutoff valve and again let any faucet in the houses hot water run. This will purge any air from your system. Next, turn the power back on and relight your pilot. 

If the drain valve won’t close tightly when you’re done, drain your tank completely, unscrew the old valve and screw in a new one. To restart the water heater, open the shutoff valve and let the hot water run at any faucet to purge air from the system. Then turn on the power or relight the pilot. A turn of the dial to set the temperature to 120 degrees, and your check is done.

Summary and Items Needed to Extend the Lifespan

Extending-Your-Water-Heaters-Lifespan-Pooles Plumbing

One of the very few items you need for this job is a simple pair of slip joint pliers.

So, that was easier than you thought, wasn’t it? Just to recap, we start off on the road to Extending Your Water Heaters Lifespan by checking your valve. So upon finding out the valve is functioning right (or if it isn’t replacing it), we moved on to emptying the tank. Once we are sure all sediment and debris are gone, we double-check everything we have done before restarting the water heater.

One last helpful hint in this process is to list materials you will need. However, it is a shortlist, as you only need four items. You need a bucket, plumbers tape, rags, and slip-joint pliers. Oh yeah, and if the pressure relief valve did not work, you will need to replace that. So, now we think you will agree that this is an easy way to help Extending Your Water Heaters Lifespan.

For more information on installation or maintaining water heaters, visit poolesplumbing.com.

Stop-a-Running-Toilet

Flushing Away the Issue: How to Stop a Running Toilet

In this our next series of helpful “at-home” plumbing tips, we will address how to deal with various toilet issues. In many cases, simple monitoring and staying on top of toilet maintenance can help to avoid any major problems. For our first article in the series, we will go through a series of steps to help you Stop a Running Toilet. 

When addressing how to Stop a Running Toilet, there are several points and parts of the toilet that you will want to look at. In doing this troubleshooting, you can find the source of this annoyance and get on fixing it before it turns costly. Luckily, not only is finding the source of the problem somewhat easy but in most cases, the fix is a simple one too.

Stop-a-Running-Toilet-Poole's

The problem with your running toilet may just be that the flapper chain is too short or too long.

What Exactly Does it Mean When My “Toilet is Running?”

Before troubleshooting, it makes sense that you are sure you know what is going on in the case your “toilet is running.” While you may know this, it certainly does not hurt to review. 

To start, after you flush your toilet, water fills into the tank. As this happens, the water lifts a float that will shut the water off after it reaches the proper level. Likewise, there is a lever that will open the toilet’s flapper, causing the actual flush. The flapper then falls back into place when the water level goes down. This process can be interrupted, causing the toilet to keep running for several different reasons that leave the bowl unfilled following a flush and in some cases still running.

As noted above, typically one of four factors are going to play into how you can Stop a Running Toilet. With a thorough check for each, the issue can be narrowed down to reveal the problem. 

Common Possible Problem Areas to Address to Stop a Running Toilet

  • Flapper Seal or Flush Valve
  • Flapper Chain
  • Leaky Fill Valve
  • Old or Corroded Toilet Handle

Start with the Seal and Valve to Stop a Running Toilet

Stop-a-Running-Toilet-Poole's Plumbing

Troubleshooting your toilet’s fill valve and its parts may result in you being able to Stop a Running Toilet.

The first area to check in the instance of a running toilet is the flapper seal or flush valve. For older model toilets, there is a chain and flapper seal. On the contrary, for newer units, there is a flush valve. These three parts in one as compared to what is seen with the older models. These three parts are the flapper seal, overflow valve, and the actual flushing mechanism. 

Whether you have a brand new toilet or the same one for years, the seal eventually can become old and warped. When a seal is compromised, the water flow from the tank to the bowl becomes prohibited. The universally known way to check if you need to replace a flapper seal or flush valve is one involving food coloring. 

Yes, food coloring…Anyhow, you simply put a few drops of your food coloring into the water in your toilet’s tank. Then, after waiting a few minutes, simply check the toilet bowl. If upon checking, you see the water has become colored in the bowl without flushing, this means you will need to replace the flapper seal or flush valve to Stop a Running Toilet.

The “Too Long…or Too Short” of it. Checking the Flapper Chain

The next point that we want to check, to Stop a Running Toilet is the flapper chain. Like our check on the seal and valve, there are a few things to look for here. First, when your toilet was initially installed, the chain may have simply been too long or short. This would cause the flapper seal in some way to not close properly.

If your chain is too short, the seal will not shut and will allow water to run continuously. Consequently, if the chain is too long, it could also get in the way of the seal closing and prevent it from forming a watertight seal. Again to restate, this can be an easy fix for you. All you need to do to Stop a Running Toilet, in this case, is adjust the chain to proper functioning length.

Give Your Handle a Lift to Check for a Leak

The third possibility that may need to be addressed to Stop a Running Toilet is a leak in your fill valve. As with our earlier discussed issues, this could cause your toilet to run continuously.

To see if this is the issue, first, flush your toilet. Once you’ve flushed, lift the toilet’s flush arm while the tank is still refilling. This will stop the water flow if all is working correctly. If the water does keep flowing and starts pouring into the overflow valve, then this is your problem. To Stop a Running Toilet in this case, you will need to replace the fill valve, as this shows it leaks.

Whether You Loosen or Replace, a Sticky Handle Needs Fixing

Stop-a-Running-Toilet-Handle

If a toilet handle is tight, loosening may work, but a corroded handle must be replaced.

The last part that we will troubleshoot to Stop a Running Toilet is the toilet handle. When checking the handle, again begin with a regular flush. If upon flushing, you notice the handle staying down instead of moving back into place, we have an issue.

The issue with your toilet handle, in this case, is that it is either old, corroded, or just stiff. Regardless, any of those three scenarios call for a fix, as the entire time a handle is in that down position, the toilet is running. To Stop a Running Toilet by fixing the handle, first, try loosening it. If it no longer sticks after flushing, you’re good to go. If loosening does not help, you will need to take a closer look and simply replace any parts that have become corroded.

Done Troubleshooting and Still Didn’t Stop a Running Toilet…Give Us a Call

If you have completed an “at home” walk through each of these possibilities and not found the problem, give us a call! The number one name in Raleigh area plumbers, Poole’s Plumbing will come out, diagnose and fix the issue. Once and for all, one way or another we will help you Stop a Running Toilet! For more plumbing tips or to contact Poole’s Plumbing about taking care of your plumbing needs, visit poolesplumbing.com.

Do-it-Yourself-Plumbing-Tips-Sink-Trap

Simple and Easy Do it Yourself Plumbing Tips

When it comes to plumbing issues, many renters and homeowners don’t think twice. It’s simply pick up the phone and call the most trusted name in Raleigh area plumbers, Poole’s Plumbing. We certainly agree with your choice of plumber…especially in a situation which calls for our help! However, becoming the “most trusted” plumber around is a name that we earned and take very seriously! Thus, we would like to share some pointers for situations where you could easily take care of the issues at hand. Therefore, here are eight easy, Do it Yourself Plumbing Tips that if following the directions below, you should be able to tackle yourself.

Do It Yourself Plumbing Tips to Silence the “Noises and Creaks” 

We have all heard them. A strange creak that at first, we are unaware of its source. Well, one of the sources of those “creaks,” we can tell you is plumbing related. The good news is, not only is it an easy fix but with our Do it Yourself Plumbing Tips, you will be able to silence that creak in no time!

Do-it-Yourself-Plumbing-Tips

The noises and creaks you hear may be coming from your copper plumbing pipes.

Silencing the Pipes

To first explain, the “creaking” comes from hot water running through copper pipes. This causes the copper to expand and when it does, the pipe grinds against the pipe hangers and joists. The easy Do it Yourself Plumbing Tips to rectify this problem are as follows.

First, get some adhesive-backed felt at a nearby hardware store. Next, you cut that felt into strips. Once strips are ready, wrap them around the “noisy pipe.” In the meantime, you will want to remove each pipe hanger and wrap the pipe with the felt tape. Finally, once wrapped, you can refasten the hanger….and you can say goodbye to the unwanted creaky sounds!

Keeping Your Sink Quiet

Yet another “noisy” plumbing issue is one that occurs and originates underneath your two-basin stainless steel sink. As anyone can attest to with this type of sink, there can be the issue of somewhat loud vibrations and the “gong” effect. Not to worry though, as this also is an issue that should be no problem for you with our Do it Yourself Plumbing Tips. Basically with this issue, you will only need a can of expanding foam.

Once you have the foam, you will use it to fill the space between the two sides of your stainless steel sink basins. You can do this when the sink has already been installed, but the procedure is a bit easier to do if you “do the filling” before installation. Once you allow the foam to harden, then trim away any excess with a knife. By filling the space, the foam works once expanded to deaden the vibrations, while it absorbs and lessens the “gong” like sound also.

Do-it-Yourself-Plumbing-Tips-Steel-Sink

One way to avoid unwanted noise is to put expanding foam between the two bays of your stainless steel sink.

More Tips to Help “Drain, Flush, and Empty” a Situation

Whether it’s your toilet, sink, a trap or pipes, if there is a clog or an obstruction, your end goal is the same. Clear it through. Again, as stated above with the “noisy” issues, there are certainly times when a clog is going to warrant a call to the pros at Poole’s Plumbing. However, in the three following situations, you will be able to take these Do it Yourself Plumbing Tips to literally “clear” the issues up yourself!

Vacuum that Toilet

As already discussed, any type of obstruction in your pipes, whether the sink, toilet, or anywhere in your home, could lead to a major plumbing problem. Almost by instinct in these cases, we always reach for the plunger first, to try and knock loose and clear the clog. But, in the case that the plunger can not clear it through, there is a good chance you are looking at a more solid or hard object that is causing the problem. In actuality, without realizing it the plunging may push this type object deeper than it was at first.

Once again, this is no reason to fret though, as all you need in many cases is a wet/dry shop vacuum. Start by sucking any water out of the area with the obstruction. Then go in deeper and many times you will find whatever object is stuck will be sucked out by the power of the vacuum.

Do-it-Yourself-Plumbing-Tips-Toilet

Several of our Do it Yourself Plumbing Tips involve ways of approaching toilet issues that you may not have thought of before.

Plunge the Trap for Less of a Mess

The curved pipe located under your sink is commonly known as the “sink trap.”Over time, the traps can get plugged up with soap, hair, and other debris. This could lead to a huge mess if allowed to get out of hand and left unattended. Regardless of whether you are just emptying the trap or changing it, this is going to be a somewhat messy job. With another of our helpful Do it Yourself Plumbing Tips, you can at very least, lessen the mess, though.

Once again, the advice here will have you utilize a common item in the home, a plunger. Simply give your drain a few plunges before pulling the trap. This will at least remove any water from the trap, which will immediately make the job a bit less messy. Do remember, however, if you have a two-sided sink, cover/plug the other drain to contain the air pressure while you plunge.

The “Flush Bucket”

The final of our Do it Yourself Plumbing Tips is one that would more than likely take place when you are already having a plumbing project take place. To put the situation into perspective, let’s say that you have the Raleigh professionals from Poole’s Plumbing set to work on your toilet. So, you would turn off the water supply before they begin their work. This would create a situation where you can not use the toilet, as there would be no water in which to flush it, right?

Well, not necessarily, as with the next of our Do it Yourself Plumbing Tips, you can still get a few uses from your toilet even in this spot. All you need to do is before shutting off the water supply, fill several two-gallon buckets with water. This way, you can flush the toilet by dumping the water into the bowl. While it won’t refill after the flush, this will still work just the same for the one flush that you would need.

The most trusted name in Raleigh area plumbing, Poole’s Plumbing is always the top choice for your plumbing emergency or project. However, the relationship we have built and trust we’ve earned over the past twenty years with our customers is how we became that way. That being said, we are always happy to come out and fix any plumbing issues you may have. But, if we can save you the headache and some money with these Do it Yourself Plumbing Tips, then we are equally as happy to pass along our knowledge.